Commision Short Adress

[kemaldede]

Hi. I can't commision the ballasts. Here is my code. I reconfigured the rst and int pins.
RST pin : C3
INT pin : A10

`#include "Click_DALI_2_types.h"
#include "Click_DALI_2_config.h"
#include "Click_DALI_2_timer.h"
#include "stdbool.h"
#include "stdint.h"

uint8_t current_state;
uint8_t numberOfBallasts = 0;
uint8_t counter;
char int_to_str[7];
char long_to_str[12];

uint32_t findDev(uint32_t base_addr, uint32_t pattern_addr, uint8_t shift_counter);
void setSearch(uint32_t addr);

void systemInit()
{
mikrobus_gpioInit( _MIKROBUS1, _MIKROBUS_INT_PIN, _GPIO_OUTPUT );
mikrobus_gpioInit( _MIKROBUS1, _MIKROBUS_RST_PIN, _GPIO_OUTPUT );

UART2_Init_Advanced(115200, _UART_8_BIT_DATA, _UART_NOPARITY, _UART_ONE_STOPBIT, &_GPIO_MODULE_USART2_PA23);

}

void applicationInit()
{
dali2_gpioDriverInit( (T_DALI2_P)&_MIKROBUS1_GPIO );
dali2_masterInit();
dali2_configTimer();
}

void applicationTask()
{
for (counter = 0; counter < 2; counter++)
{
dali2_sendCmd(_DALI2_ADDRESS01, _DALI2_OFF, _DALI2_BROADCAST_CMD, _DALI2_FOLLOWING_COMMAND);
Delay_ms( 1000 );
dali2_sendCmd(_DALI2_ADDRESS01, _DALI2_RECALL_MAX_LEVEL, _DALI2_BROADCAST_CMD, _DALI2_FOLLOWING_COMMAND);
Delay_ms( 1000 );
}

for (counter = 0; counter < 8; counter++)
{
    dali2_sendCmd(_DALI2_ADDRESS01, _DALI2_DOWN, _DALI2_BROADCAST_CMD, _DALI2_FOLLOWING_COMMAND);
    Delay_ms( 500 );
}

for (counter = 0; counter < 8; counter++)
{
    dali2_sendCmd(_DALI2_ADDRESS01, _DALI2_UP, _DALI2_BROADCAST_CMD, _DALI2_FOLLOWING_COMMAND);
    Delay_ms( 500 );
}

}

uint8_t setDevAddress(uint8_t start_addr){

uint32_t addr_dev = 0xFF;

// UART2_Write_Text("Arama islemi basliyor....");
dali2_sendCmd(_DALI2_ADDRESS01, _DALI2_RESET, _DALI2_BROADCAST_CMD, _DALI2_FOLLOWING_COMMAND);
Delay_ms( 100 );
dali2_sendCmd(_DALI2_ADDRESS01, _DALI2_RESET, _DALI2_BROADCAST_CMD, _DALI2_FOLLOWING_COMMAND); // Balastlar resetleniyor
Delay_ms(100);
dali2_sendCmd(_DALI2_ADDRESS01, _DALI2_OFF, _DALI2_BROADCAST_CMD, _DALI2_FOLLOWING_COMMAND); // Lambaları söndür
Delay_ms( 300 );

dali2_sendCmd(_DALI2_ADDRESS01,_DALI2_INITIALISE,_DALI2_BROADCAST_CMD, _DALI2_FOLLOWING_COMMAND);   // Initialize komutu
Delay_ms(100);
dali2_sendCmd(_DALI2_ADDRESS01,_DALI2_INITIALISE,_DALI2_BROADCAST_CMD, _DALI2_FOLLOWING_COMMAND);
Delay_ms(100);
dali2_sendCmd(_DALI2_RANDOMISE_L,_DALI2_RANDOMISE_H,_DALI2_BROADCAST_CMD, _DALI2_FOLLOWING_COMMAND);     // Ramdomize komutu
Delay_ms(100);
dali2_sendCmd(_DALI2_RANDOMISE_L,_DALI2_RANDOMISE_H,_DALI2_BROADCAST_CMD, _DALI2_FOLLOWING_COMMAND);
Delay_ms(100);

while(1){
    addr_dev = findDev(0xFFFFFF, 0x800000,0);
                    
    if (addr_dev == 0xFFFFFFFF)       //Adreslemeden çıkılıyor
        break;
        
    UART2_Write_Text("Device Found!!!!");
    UART2_Write(13);
    UART2_Write(10);
    setSearch(addr_dev);   // Search komutu ile
    dali2_sendCmd(((start_addr << 1) | 0x01),_DALI2_PROGRAM_SHORT_ADDRESS, _DALI2_COMMAND,_DALI2_FOLLOWING_COMMAND); // Kısa adres programlandı
    Delay_ms(100);
    dali2_sendCmd(_DALI2_WITHDRAW_L, _DALI2_WITHDRAW_H, _DALI2_COMMAND,_DALI2_FOLLOWING_COMMAND);   // Kısa adresi atanan ballast arama döngüsünden çıkarılıyor
    Delay_ms(100);
    start_addr++;
    numberOfBallasts++;
}
dali2_sendCmd(_DALI2_TERMINATE_L_BITS, _DALI2_TERMINATE_H_BITS, _DALI2_BROADCAST_CMD,_DALI2_FOLLOWING_COMMAND);   // Terminate komutu
return start_addr;

}

uint32_t findDev(uint32_t base_addr, uint32_t pattern_addr, uint8_t shift_counter){

uint8_t ballast_response;

setSearch(base_addr);
dali2_sendCmd(_DALI2_COMPARE_L,_DALI2_COMPARE_H,_DALI2_BROADCAST_CMD, _DALI2_FOLLOWING_COMMAND);       // Compare komutu
Delay_ms(10);
ballast_response = dali2_getBallastResponse();

if(ballast_response){
    if (shift_counter == 24)
        return base_addr;
    else
        base_addr -= pattern_addr;
} 
else {
    if (shift_counter == 0){
        UART2_Write_Text("Device Not Found!!!");
        UART2_Write(13);
        UART2_Write(10);
        return 0xFFFFFFFF;
    }
    else if (shift_counter > 23){
        return (base_addr + 1);
    }
    else{
        base_addr += pattern_addr;
    }
        
}

if (shift_counter != 23){
    pattern_addr >>= 1;
}
            
shift_counter++;

base_addr = findDev(base_addr, pattern_addr, shift_counter);
return base_addr;

}

void setSearch(uint32_t addr){

 uint8_t searchAdrrH,searchAdrrM,searchAdrrL;
 char long_to_hex[9];
 searchAdrrH = ((addr >> 16) & 0xFF);
 searchAdrrM = ((addr >> 8) & 0xFF);
 searchAdrrL = (addr & 0xFF);
 
 LongIntToHex(addr,long_to_hex);
 UART2_Write_Text(long_to_hex);
 UART2_Write(13);
 UART2_Write(10);
 
 dali2_sendCmd(searchAdrrH,_DALI2_SEARCHADDRH,_DALI2_COMMAND, _DALI2_FOLLOWING_COMMAND);
 Delay_ms(30);
 dali2_sendCmd(searchAdrrM,_DALI2_SEARCHADDRM,_DALI2_COMMAND, _DALI2_FOLLOWING_COMMAND);
 Delay_ms(30);
 dali2_sendCmd(searchAdrrL,_DALI2_SEARCHADDRL,_DALI2_COMMAND, _DALI2_FOLLOWING_COMMAND);
 Delay_ms(30);

}

void main()
{
uint8_t n_dev = 0;
systemInit();
applicationInit();
applicationTask();
n_dev = setDevAddress(0x00);

    while(1){
    
        dali2_sendCmd(_DALI2_ADDRESS01, _DALI2_RECALL_MAX_LEVEL, _DALI2_COMMAND, _DALI2_FOLLOWING_COMMAND);
        Delay_ms( 1000 );

        for (counter = 0; counter < 8; counter++)
        {
            dali2_sendCmd(_DALI2_ADDRESS01, _DALI2_DOWN, _DALI2_COMMAND, _DALI2_FOLLOWING_COMMAND);
            Delay_ms( 500 );
        }

        for (counter = 0; counter < 8; counter++)
        {
            dali2_sendCmd(_DALI2_ADDRESS01, _DALI2_UP, _DALI2_COMMAND, _DALI2_FOLLOWING_COMMAND);
            Delay_ms( 500 );
        }
        
        dali2_sendCmd(_DALI2_ADDRESS01, _DALI2_OFF, _DALI2_COMMAND, _DALI2_FOLLOWING_COMMAND);
        Delay_ms( 1000 );
        
    }

}`

[busy-reiding]

Hi there, I was wondering if you were able to figure this out? I’m having some trouble with it too.

[kemaldede]

Unfortunately, I can't. Seems no one give us some help from mikroe team